Hw133v10 Datasheet Page

An official NTE Electronics datasheet specifically for the was not found in publicly available sources. However, the comprehensive data for the base HW133 model is widely accessible and can be used to determine the core parameters of the V10 variant. The following table presents the confirmed specifications for the standard HW133, which form the baseline for the entire family:

It is significantly smaller than the older LM2596 modules, making it a "go-to" choice for weight-sensitive applications like quadcopters. দারাজ Usage Notes Buck Mode: As a step-down converter, the input voltage must always be higher

The "HW133" designation historically belongs to highly stable adapter and IC systems designed to interface complex multi-pin packages (such as HQ208 or CS144 chip scale packages) with standard hardware programmers, test fixtures, or carrier boards. The extension signifies Version 1.0 of the specific printed circuit board (PCB) routing configuration or silicon layout. Primary Operational Features hw133v10 datasheet

The HW133V10 is a widely used , typically found in consumer electronics, automotive dashboards, and industrial interfaces. While specific datasheets for exact version revisions like "v10" are often proprietary to the manufacturer (such as Ampire or Chimei Innolux), they share standard characteristics with the 13.3-inch TFT-LCD family. Core Technical Specifications

Peak performance rating exceeding 93% under typical load configurations, significantly minimizing parasitic heat generation. An official NTE Electronics datasheet specifically for the

Always ensure the host microcontroller and the HW133V10 board share a unified ground potential to eliminate floating data states. Troubleshooting Fault Conditions

Traced to minimize length mismatches, ensuring that parallel data bytes arrive synchronously without phase distortion. Power Distribution & Noise Decoupling দারাজ Usage Notes Buck Mode: As a step-down

Without the official HW133V10 datasheet, engineers risk:

When routing Pin 8 to an external power MOSFET, integrate a small 10-to-100 Ohm resistor to dampen parasitic high-frequency oscillations along the gate trace.

| Parameter | Specification | Unit | Remarks | | :--- | :--- | :--- | :--- | | | | | | | Manufacturer | BOE HYDIS | - | Also known as BOE or Hydis | | Model Name | HV133WX1-100 | - | | | Size | 13.3" (diagonally) | inch | | | Technology | a-Si TFT-LCD | - | Active Matrix LCD | | Physical Characteristics | | | | | Resolution | 1280 x 800 (WXGA) | pixels | 16:10 aspect ratio | | Pixel Pitch | 0.2235 x 0.2235 | mm | | | Active Area | 286.08 x 178.80 | mm | | | Outline Dim. | 301.4 x 196.5 x 6.5 (Max) | mm | | | Weight | 275g (Typ.) ±10g | g | | | Electrical Specifications | | | | | Logic Supply Voltage | 3.3V (Typ.) | V | 3.0V min, 3.6V max | | Logic Current | 360mA (Typ.) | mA | | | Backlight Supply | 12.0V (Typ.) | V | 5.0V min, 21.0V max | | Backlight Current | 271mA (Typ.) | mA | | | Backlight Type | SMD LED Array | - | 54 LEDs (9 series x 6 parallel) on bottom side | | Interface | 1 channel LVDS | - | Low-Voltage Differential Signaling | | Optical Specifications | | | | | Display Mode | Normally Black, FFS | - | Fringe Field Switching for wide viewing angles | | Luminance (Brightness) | 300 cd/m² (Typ.) | cd/m² | | | Contrast Ratio | 500:1 (Typ.) | - | | | Viewing Angle (L/R/U/D) | 89/89/89/89 (Typ.) | degrees | CR ≥ 10 | | Color Depth | 262,144 colors | - | 6-bit color depth | | Response Time | 30ms (Typ.) (Tr+Td) | ms | |

Below is a comprehensive technical overview of the HW133V10, detailing its specifications, installation requirements, and operational safety.